Down to Earth EMF Services

EMF Surveys that don't cost the earth

EMF Surveys that don't cost the earth

EMF Surveys that don't cost the earthEMF Surveys that don't cost the earthEMF Surveys that don't cost the earth



The Acousticom-2 is EMFields newest microwave detector and it was designed using the experience gained from many years of practical RF and microwave measurements. The meter presents RF measurements as an audio signal, with LEDs and an alarm at high levels of RF (you can also switch the sound off if you prefer to be less obvious when taking readings).

LED lights display the peak levels of microwave electromagnetic fields from 200 MHz up to over 8000 MHz (8 GHz), covering the frequencies used by most modern communication systems encountered in our everyday environment. This includes all mobile phone systems including 4G/LTE, Smart Meters, all WiFi and WiMax frequencies, DECT cordless phones and baby monitors. The LEDs update rapidly, and allow you to quickly gauge the levels in an area and find any hot-spots. Its readout is sensitive to 0.01 V/m. When two LEDs are both lit next to each other, the exposure level is halfway between the two. This is only for levels above 0.1 V/m, e.g. when both 0.10 and 0.30 V/m are lit, the level is about 0.20 V/m (halfway between).

The Acousticom 2 reacts to very short pulses. Peak readings are what they say - the highest sampled reading - though the sampling and processing rate means that there are some gaps and it will not always react to a SINGLE VERY short pulse (less than about 5 microseconds duration) - though it will react correctly to much shorter pulses that are regularly transmitted (such as from WiFi). 

When first turned on the Acousticom 2 is silent. The sound may be turned on and off by pressing the button. The Acousticom 2 also has an "alarm" sounder which emits a pulsing warning at higher exposure levels. If the alarm is not required, then it is easy to disable it each time when you turn the Acousticom 2 on. The demodulated sounds allow you to determine, with a small amount of practice, what type of device is creating the pulsing microwave levels that are present. These features make the instrument the most useful and practical one available - even for people with severe electrosensitivity.

Sound samples are available on the EMFields website and also on Safe Living Technologies website to help you identify what kind of signal the Acousticom 2 is measuring. The sounds made by different transmitters can change with time, so these are meant as a rough guide only. If you are subject to a number of sources of RF, the sounds may intermingle and be less easily identified.

The internal antenna is at the upper half of the case and the back. Signals are best measured when the source is behind the instrument, but also quite good with the source to one side or other the other. Turn the Acousticom 2 for the highest reading.

Technical Specifications:

  • Frequency range: 20Hz - 50kHz

  • A line of coloured LEDS displaying Peak exposure levels in V/m

  • Measurement range: 200 - 8 000 MHz ±6 dB (typical accuracy)

  • Sensitivity (Peak Display): 0.01 - 6.00 volts per metre (V/m) 0.01  0.02  0.05  0.1  0.3  1.0  3.0  6.0 V/m;   (equivalent to 0.5 to 100,000 peak µW/m2)

  • Some intermediate points when two LEDs are both lit are also defined:    0.2  0.6  2.0  4.5 V/m

  • The speaker may be switched on and off

  • An alarm sounder at higher exposure levels (may be disabled)

  • Power source: 1x PP3/MN1604 9 volt Alkaline or Rechargeable

  • Power draw: 40 to 90 mA (depends on the sound volume)

  • Battery life: Up to 10 hours continuous with normal alkaline battery   » Low battery indicator light (the green 'on' light turns red)

  • Size (mm): 110 x 63 x 21 (LxWxD); Weight: 140g incl. battery